community-content

Forum Replies Created

Viewing 15 posts - 3,046 through 3,060 (of 9,648 total)
  • Author
    Posts
  • in reply to: Message Assignment – Biztalk Expression Editor #21994

    If you by saying: “I reference my class in the Biztalk Expression Editor” mean “Write the correct namespace path”, you also have to make a reference in your project to your ScriptingFunctions project/assembly.

    Then your assembly also need to exist in the GAC later on when running.

    Kind Regards
    Martin Bring

    in reply to: Problem with moving BizTalk databases to antoner server #21993

    Did you cun the script to update config and registry? I did similar move last week on my BizTalk 2006 R2 server.

    There should be a script and sampleupdate schema under the <drive>BizTalk Server… /Schemas/Restore

    Check if you done the below changes.

    1. After moving database to new server, ensure all the log in sercurite and previlages are same as old server.

    2. make sure new server MSDTC accept in and out bound network transaction

    3. Stop BizTalk applications, Enterprice Applications from services

    4. Go to ProgramFiles/BizTalk server.. / Schemas/ Restore/SampleUpdateInfo.xml

    5. Replace all SourceServer with your old db server name

    6. Replace all Destination Server with your new DB server name

    7. Uncomment the database updates in that file if u needed

    8. run the following scripts from command prompt and make sure they are success

          a. Run cscript UpdateDatabase.vbs SampleUpdateInfo.xml
         b. Run cscript UpdateRegistry.vbs SampleUpdateInfo.xml

    9. Restart ESSO and BTS applications, Windows Management Instructions

    10. Remove the old group from BizTalk Admin conlose and select the new one from existing connections

    11. Ensure all the database update are correct in BizTalk Config console

    12. Update Receive port if you are using EDI Batching under the BizTalk EDI Application

    Hope these will helps you,

    Siva

     

    in reply to: Tranformation on a Orch #21992

    I think may be your map’s destination message type doesnt not exist in your orchestration messages, map is messed up or something wrong with reference for the destination message type. If you want, you can send the sample project to my email and I will take a look at it.

    You are right.  One of the send ports archives the incoming message, so it outputs the original message to a folder with a File Adapter.

    Of course, now I have to figure out what other filter I would use on the receive shape to be sure it’s not subscribing to those archived messages.   That is a puzzle for me.  Any suggestions would be appreciated.

    Thanks.

    I think that a component will need to be the answer.  The ISA fields are in the header of the original message, so can’t be promoted in a schema (so far as I know) – otherwise, no problem.

    Fundamentally , this is a question about how to write C# in the Message Assignment and Expression Shapes.  Does anyone know of a tutorial that addresses this?  My fumbling around with ‘guessing’ what is available and not in these shapes is very frustrating.

    Thanks for the help.

    in reply to: Tranformation on a Orch #21987

    Hi, No I am not using source control..

    in reply to: Uploading a generated file – results in "file not found" #21985

    You do not specify using an orchestration, but it sounds like.

    If so, mark the first logical send port as “Delivery Notification”  = Transmitted. then the orch will wait until the message has been sent.

    Kind Regards
    Martin Bring

    in reply to: Tranformation on a Orch #21983

    Are you using source control?

    If the map is under source control, then it behaves as you have described.

    Check out your map and it would allow you to configure the transform shape and the map.

    Cheers

    Bibhakar Saran

     

    Soundslike you have created yourself a loop.
    A direct bound port without any additional filters will subscribe to any messages of the type specified on the activate receive shape.

    If you subsequently send the same message type out a send port, then another instance of the orchestration will begin, over and over.

    Are you sending the same message type out one of the send ports?

    in reply to: BAM Pipeline interceptor with Envelope debatching #21978

    Have any of you guys been able to resolve this? I’m running into the same issue – please share [:D]

     

    Thanks!

    in reply to: Tranformation on a Orch #21977

    When you are in the transform shape, I select existing map point it towards the existing map I have in the referenced project, select the inbound message but it does not give me the option to select the outbound message..

    Thanks.

    in reply to: Mapping problem, need ideas please. #21975

    Insted of using the maaping functoids you can use custom XSLT which will able to do what loging you want to do…..

    Amol Pande

    in reply to: Mapping problem, need ideas please. #21974
    in reply to: Tranformation on a Orch #21973

    Could you give me more info? I am just biggner too.

    Info such as when do you get error, what is the error message or screen shot.

    in reply to: Tranformation on a Orch #21972

    Siva, Yes I have referenced the schema project and yes I have created messages for each schema…

     

    Any ideas?

Viewing 15 posts - 3,046 through 3,060 (of 9,648 total)