EDI document rejected by BizTalk

Home Page › Forums › BizTalk 2004 – BizTalk 2010 › EDI document rejected by BizTalk

Viewing 1 reply thread
  • Author
    Posts
    • June 8, 2010 at 12:48 AM #24903
      community-content

        I’m trying to submit a EDI document to BizTalk but it is getting rejected because of the following (error message as found in the Event Log):
        The sender of the document is not recognized. Contact the system administrator. (msgnr:0 segnr:0)(line:2 pos:1 filepos:362)sender: [][] [9313938000631][ZZ][]sender: [][] [9313938000631][ZZ][]

        Looking  in the Parties folder in the BizTalk administration console I can see that the following party has been created
        EDI://9313938000631:ZZ:9313938000631

        The EDI schema being used is EFACT_D01B_ORDERS.xsd and below is the message being submitted to BizTalk.

        UNB+UNOA:3+9313938000631:ZZ+9331849499994:ZZ+060829:1141+2++++1++1′
        UNH+2+ORDERS:D:01B:UN:EAN010′
        BGM+220+R-06228A+9′
        DTM+137:20060829:102′
        DTM+2:20060906:102′
        NAD+BY+9313938000631::9′
        NAD+ST+9315GR::92′
        NAD+SU+156001::92′
        LIN+1++9314250041845:SRV’
        QTY+21:15′
        DTM+15:20060912:102′
        PRI+1E:9.9′
        LIN+2++9356452341123:SRV’
        QTY+21:30′
        PRI+1E:11.9′
        LIN+3++9123456741329:SRV’
        QTY+21:20′
        PRI+1E:6.9′
        LIN+4++9314250987654:SRV’
        QTY+21:10′
        PRI+1E:9.5′
        LIN+5++9314250066666:SRV’
        QTY+21:25′
        PRI+1E:8.9′
        UNS+S’
        MOA+86:961′
        CNT+2:5′
        UNT+27+2′
        UNZ+1+2′

        Any help is highly appreciated.

        Cheers,

      • June 8, 2010 at 1:13 PM #24913
        community-content

          Hi,

           

            Did you configure the Edi properties for this party? Specifically, the Party as Interchange Sender information under the Edifact Properties entry…

           

            Daniel.

           

          • June 8, 2010 at 5:31 PM #24917
            community-content

              Hi Daniel,

              No I haven’t configured any of the EDI Properties for this party. I should have mentioned that the Base EDI adapter is being used and not native EDI functionality. The scenario is basically the following:

              A file receive location configure with the Base EDI adapter EDI://9313938000631:ZZ:9313938000631 and an passthrough send port subscribing to the receive port.

              • June 9, 2010 at 8:14 AM #24928
                community-content

                  Hi,

                   

                     Ok, I see yours was an existing installation of BizTalk Server (with Base EDI Adapter installed) and you upgraded it to version 2006 R2. I am not familiar with that type of setup but you might want to check the following article for interoperability issues (just for your reference, and this may or may not relate to the problem you are having):

                  http://help.outlook.com/en-us/140/bb246054(v=BTS.20).aspx

                   

                     Best,

                   

                     Daniel.

                   

                  • June 9, 2010 at 5:20 PM #24933
                    community-content

                      Hi Daniel,

                      Yes exactly it is on of those exiting installations:-) Thanks for the link I’ll read it through.

                      Cheers,

            • Author
              Posts
            Viewing 1 reply thread
            • The forum ‘BizTalk 2004 – BizTalk 2010’ is closed to new topics and replies.